Baumatic BKF24ID Manuel d'utilisateur

1BKF24ID 60cm Front touch control induction zone hob

Electrical details 10 Vac 50 - 60 Hz sed outlet with 3mm contact gap) chase which can be und on your sales invoice. The rating plate of your hob

Control panel layout 11uttons er button control 7) Function buttons mic hob 1) Cooking zone selection b2) ON / OFF pow3) Plus and minus buttons 4)

12and all the indicator lights will turn on for about 1 second then switch off again. After this, the hob will enter stand-o selection button (1) of

13MPORTANT: The cooking zone will return to stand-by mode if in 1 minute of pressing the ON / FF button. ber in the cooking zone indicator reaches “0

14ne is switched off, the corresponding cooking zone indicator will show a flashing letter 60°C and is therefore still high enough to cause injury. o

15es not mean that there is an appliance fault. IMPORTANT: You should make sure that all pans are placed in he boost function tain a faster and more

16o The table be zone. MAX power (kW)low shows the booster power of each Cooking zone Normal Boost Front left 2.20 2.90 Rear left 1.50 2.00 Re

17e selection button (1) followed by the fry function button again g the relevant cooking zone, to switch off the fry function, set the power level

18o This timer function can be applied to each burner separately by RNING: It is vital that you do not leave the hob unattended our hob also has an

19o If the safety lock is activated when the cooking zones are not in er indicator will show “Lo” for 1 minute when the hob o Based on the power le

User Manual for your Baumatic BKF24ID 60 cm Touch control induction zone hob NOTE: This User Instruction Manual contains i

20o When cold, the bottom of the pans should be slightly concave, as o The best thickness for the bottom of the pans is 2 – 3 mm of o If these rul

Cleaning and maintenance m your fore commencing any cleaning n easier to clean some deposits whilst the hob till warm. You should take care not to bu

22 hob scraper will be provided with your appliance. The llowing guidelines should be followed when using the ceramic hob craper:- o Residues shou

23irature rise of 85°C above the ambient temperature of the room it is located in, during itchen unit (depending on size) or 600 mm worktop that is

Unpacking the appliance When unpacking the appliance please check that the following items are contained within the p

Installing the appliance o Cut a hole in the worktop that corresponds with the drawing shown above. o If the hob is being installed without an o

o IMPORTANT: There are ventilation holes around the outside of the hob. YOU MUST ensure that these holes are not blocked by

o Carefully turn the hob back over and then gently lower it into the aperture hole that you have cut out. o There are holes on the base o

Connecting the mains supply cable o The mains terminal block is located on the underside of the hob and the terminals are accessible by removing the

o Open the terminal block on the underside of the hob. o Unscrew the terminal screws fixing the cable. o Replace the cable with one of the same l

3Contents Environmental note 4 Important safety information 5 – 8 Specifications 9 – 11 Product and aperture dimensions 9 Prod

30o A humming sound is heard when a cooking zone is selected. * This is normal; the sound will disappear when the zone heats up. o The cooking z

IMPORTANT: If your appliance appears not to be operating correctly, then you should disconnect it from your mains supply and then contact an Authoris

32

33

34

35

3636

Environmental note 4 o The packaging materials that Baumatic uses are environmentally friendly and can be recycled. all packaging mat

5Important safety information Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before at

6o Repairs may only be carried out by an Authorised Service Log onto www.applico.co.nzAgent. to locate a Service Agent nearest to you. . commend t

7gislation regarding electro-magnetic interference and is designed not to interfere with other gulations. If in doubt, you should consult the manufac

8Declaration of conformity Th of mending Directive 92/31/EEC. ed materials and requires the appliance to be installed in rrently in force. This appl

Specifications Product dimensions: Aperture dimensions: Depth: 520 mm Depth: 490 mm Width: 590 mm Width: Height: 55 mm 560 mm Heigh