Baumatic BGG74 Manuel d'utilisateur

el 1BGG30 / BGG32 / BGG60 / BGG64 / BGG70 / BGG74 Gas hobs

BGG70 / BGG74 10 Width: 560 mm urner burner device on each burner s o Wok stand Product dimensions: Aperture dimensions: Depth: 480 mm Dep

11Rated Voltage: / 60 Hz ole switched fused outlet with ax Rated Inputs: 0.0008 kW y Lead: 3 core x 0.75mm² (Type RR-F <HAR> marked) onn

12ace layout = 3.80 kW triple crown (wok) burner = Control panel ary burner = 3.00 kW rapid burner = Control panel er rapid burne

BGG64 A = 1.00 kW auxiliary burner B = 1.75 kW semi-rapid burner C = 3.80 kW triple crown (wok) burner D = Control panel BGG70 13-rapid burne

14hob Using the gas Before ou should clean the hob surface. “Cleaning and maintenance” section). bols will appear on the control panel, next to eac

15o You should hold down the control knob for 20 seconds after the 20 second interval, turn the control knob to your required setting between the m

Cleaning Cleaning 16 operations must only be carried out when the hob is cool. The appliance supply before should be disconnected from your mains co

17o IMPORTANT: Make sure that you reassemble the burners in the o IMPORTANT: Make sure that the hob surface and pan stands t, damp cloth that has b

18irature rise of 85°C above the ambient temperature of the room it is located in, during d: BGG32) sitting room. IMPORTANT: The appliance must not

19ce is sufficient. HOWEVER sufficient space must be allowed for saucepan handles to be turned and for f the underside of the horizontal surface is l

User Manual for your Baumatic BGG30 / BGG32 30 cm Burner gas hob BGG60 / BGG64 60 cm 4 Burner gas hob BGG70 / BGG74 70 cm 5 Burner gas hob

20GG30 / BGG32 BGG60 / GG70 B BGG64 B / BGG74

21ls All mode o IMPORTANT: You must have a gap of at least 25 mm between the underneath of the appliance and any surface that is below it.

o Place the clamp (B) over the holes that match the size of the screws. There are one set of screw holes in each corner of the hob. Slightly tighten

23Ventilation requirements o The room containing the hob should have an air supply in accordance with the current edition of BS 5440: Part 2: o

Gas Safety (Installation and Use) Regulations IMPORTANT: The appliance MUST be connected to the gas supply by use of a 15 mm x ½” female coupler, sea

Gas adjustment (Conversion to LPG) All work must be carried out by a GASSAFE registered engineer. IMPORTANT: Always isolate the hob from the electri

Minimum flow adjustment for hob gas taps. All work must be carried out by a GASSAFE registered engineer. IMPORTANT: Always isolate the hob from the

Gas tap maintenance These maintenance operations MUST ONLY be carried out by a GASSAFE registered engineer. IMPORTANT: Before carrying out any maint

Electrical connection This appliance must be installed by a qualified person in accordance with the latest edition of the I.E.E. Regulations and in c

My appliance isn’t working correctly IMPORTANT: If your appliance appears not to be operating correctly, then you should disconnect it from your main

3Contents Environmental note 4 Important safety information 5 – 7 Specifications 8 – 13 BGG30 / BGG32 8 BGG60 / BGG64

30Baumatic Consumables o BC001 Degreaser for Dishwashers (200 g) o BC002 Descaler for Washing Machines and Dishwashers (200 g) o BC003 Ceramic

31 United Kingdom Baumatic Ltd., Baumatic Buildings, 6 Bennet Road, Reading, Berkshire RG2 0QX United Kingdom Sales Telephone (0118) 933 6900 Sales

32

Environmental note o The packaging materials that Baumatic uses are environmentally friendly and can be recycled. all packaging mater

5Important safety information Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before at

6hild Safety ce at any time. During and after use, all surfaces will be hot. se ensure that they are kept under close supervision at all times. uld o

7leaning Cleaning of the hob should be carried out on a regular basis. appliance, it should be disconnected from the mains and cool. using this ap

8 8pecifications S BGG30 / Width: 268 mm Product specifications (B burner GG32 only) BGG32 Product dimensions: Aperture dime

9GG Width: 560 mm ): urner burner device on each burner (BGG64 only) o B 60 / BGG64 Product dimensions: Aperture dimensions: Depth: 480 m